Illinois Railway Museum Home Page
 BLOG | DIRECTIONS | SCHEDULE | STORE |
   
 
 GN 70104 
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
IN THIS PHOTO BY BOB KUTELLA, THE AIRBRAKES ON THE HOPPER ARE BEING TESTED BY KIRK WARNER.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
HEROLD WIND IS GRINDING OFF THE RIVETS SO THAT THE HANDHOLDS CAN BE REMOVED PRIOR TO THE NEW SUPPORT INSTALLATION.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
NEIL SCHWINBECK IS CUTTING THE DAMAGED VERTICAL HANDOLD SUPPORT.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
THE DAMAGED VERTICAL HANDHOLD SUPPORT HAS BEEN REMOVED.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
IN THIS PHOTO BY BOB KUTELLA, THE AIRBRAKES ON THE HOPPER ARE BEING TESTED BY KIRK WARNER. - Kirk L. Warner (kwarner)
Viewed: 724 times.
HEROLD WIND IS GRINDING OFF THE RIVETS SO THAT THE HANDHOLDS CAN BE REMOVED PRIOR TO THE NEW SUPPORT INSTALLATION. - Kirk L. Warner (kwarner)
Viewed: 657 times.
NEIL SCHWINBECK IS CUTTING THE DAMAGED VERTICAL HANDOLD SUPPORT. - Kirk L. Warner (kwarner)
Viewed: 671 times.
THE DAMAGED VERTICAL HANDHOLD SUPPORT HAS BEEN REMOVED. - Kirk L. Warner (kwarner)
Viewed: 641 times.
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
JOHN FAULHABER SHOWS THE NEWLY INSERTED VERTICAL HANDHOLD SUPPORT.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.03.08 - TWO OF THE DAMAGED VERTICAL HANDRAIL SUPPORTS HAVE HAD THE DAMAGED SECTIONS REMOVED AND NEW PIECES WELDED IN PLACE TO REPAIR THE DAMAGE.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.03.08 - NEIL SCHWINBECK HAS CUT OUT THE DAMAGED SECTION OF THE SIDESILL IN PREPARATION FOR APPLICATION OF A NEW PIECE.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.12.08 - BOB KUTELLA IS LAYING OUT THE POINTS TO DRILL FOR THE HANDHOLD ATTACHMENTS ON THE VERTICAL SUPPORT.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
JOHN FAULHABER SHOWS THE NEWLY INSERTED VERTICAL HANDHOLD SUPPORT. - Kirk L. Warner (kwarner)
Viewed: 663 times.
10.03.08 - TWO OF THE DAMAGED VERTICAL HANDRAIL SUPPORTS HAVE HAD THE DAMAGED SECTIONS REMOVED AND NEW PIECES WELDED IN PLACE TO REPAIR THE DAMAGE. - Kirk L. Warner (kwarner)
Viewed: 685 times.
10.03.08 - NEIL SCHWINBECK HAS CUT OUT THE DAMAGED SECTION OF THE SIDESILL IN PREPARATION FOR APPLICATION OF A NEW PIECE. - Kirk L. Warner (kwarner)
Viewed: 689 times.
10.12.08 - BOB KUTELLA IS LAYING OUT THE POINTS TO DRILL FOR THE HANDHOLD ATTACHMENTS ON THE VERTICAL SUPPORT. - Kirk L. Warner (kwarner)
Viewed: 627 times.
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.12.08 - BOB KUTELLA IS DRILLING ANOTHER HOLE TO MOUNT THE HANDHOLD TO THE REPLACED VERTICAL SUPPORT.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.07.09 - WORK ON THIS CAR RESUMED TODAY.  HERE BOB KUTELLA SUPERVISES A CONTRACT WELDER WHO WAS REPAIRING OR REPLACING BENT PARTS OF THE CAR.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.07.09 - BRUCE PLAXTON IS GRINDING WELDS WHERE NEW PIECES OF STEEL WERE APPLIED TO CORRECT DAMAGE ON THE CAR.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
10.07.09 - THE CONTRACT WELDER IS WELDING PART OF A VERTICAL SUPPORT BACK TOGETHER  AFTER CUTTING IT TO HEAT AND STRAIGHTEN THE PART.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
10.12.08 - BOB KUTELLA IS DRILLING ANOTHER HOLE TO MOUNT THE HANDHOLD TO THE REPLACED VERTICAL SUPPORT. - Kirk L. Warner (kwarner)
Viewed: 665 times.
10.07.09 - WORK ON THIS CAR RESUMED TODAY. HERE BOB KUTELLA SUPERVISES A CONTRACT WELDER WHO WAS REPAIRING OR REPLACING BENT PARTS OF THE CAR. - Kirk L. Warner (kwarner)
Viewed: 796 times.
10.07.09 - BRUCE PLAXTON IS GRINDING WELDS WHERE NEW PIECES OF STEEL WERE APPLIED TO CORRECT DAMAGE ON THE CAR. - Kirk L. Warner (kwarner)
Viewed: 860 times.
10.07.09 - THE CONTRACT WELDER IS WELDING PART OF A VERTICAL SUPPORT BACK TOGETHER AFTER CUTTING IT TO HEAT AND STRAIGHTEN THE PART. - Kirk L. Warner (kwarner)
Viewed: 757 times.
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
06.30.10 - MIKE ALTERIO INSTALLS A RIVET ON A LADDER ON THE CAR.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
FRAME
FRAME
FRAME
06.30.10 -  KIKE ALTERIO HEATS A BENT PORTION OF THE CAR WHILE VICTOR HUMPHREYS WAITS TO USE THE SLEDGE HAMMER TO STRAIGHTEN THE PART.
FRAME
FRAME
FRAME
FRAME
FRAME FRAME FRAME
FRAME
06.30.10 - MIKE ALTERIO INSTALLS A RIVET ON A LADDER ON THE CAR. - Kirk L. Warner (kwarner)
Viewed: 347 times.
06.30.10 - KIKE ALTERIO HEATS A BENT PORTION OF THE CAR WHILE VICTOR HUMPHREYS WAITS TO USE THE SLEDGE HAMMER TO STRAIGHTEN THE PART. - Kirk L. Warner (kwarner)
Viewed: 366 times.
Powered by Gallery.
Copyright © 1995-2014, Illinois Railway Museum. All rights reserved. Last Modified: 05/11/10 11:20:24 PM